3GR36/25W2三螺桿泵、特制三螺桿泵裝置
3GR螺桿泵采用了上被認為輸送泵的一點連續接觸齒輪,即雙圓弧加正弦曲線復合成齒形,可*淘汰漸開線齒輪輸送泵,圓弧齒輪在兩嚙合齒廓間為一點連續接觸,不會產生困油現象,*解決了漸開線齒輪泵因困油現象導致泵的振動,噪聲,軸承負載增大等現象.因此3GR螺桿泵具有效率、噪聲低,并具有良好的節能效果。
3GR screw pump is internationally considered a little pump of the most advanced continuouscontact gear, namely double arc sine curve plus compound into a tooth, can be compley out of the involute gear pump, circular arc tooth profile gear meshing between the twocontinuous contact for the point, does not produce oil phenomena, solve the involute gearpump for trapped oil phenomenon caused by the pump vibration, noise, bearing the load increases and so on. So the 3GR screw pump has efficiency, low noise, and good energy saving effect.
曾獲*重大科技成果項目,并獲國家教委科技進步三等獎。
The major scientific and technological achievements project won the national scientific and technological progress, and won the three prize of the State Education commission.
3GR螺桿泵介紹和啟動前的準備.
3GR screw pump is introduced and the preparations before startup.
本系列3GR螺桿泵主要有齒輪、軸、泵體、泵蓋、軸承套、軸端密封等組成。齒輪采用雙圓弧正弦曲線齒形制造。它與漸開線齒輪相比zui突出的優點是齒輪嚙合過程中齒廓面沒有相對滑動,所以齒面無磨損,運轉平穩,無因液現象,噪音低、壽命長、效率高。該泵擺脫了傳統設計的束縛,使得齒輪泵在設計、生產和使用上進入了一個新的領域。
The series of 3GR screw pump main gear, shaft, pump body, pump cover, bearings, shaft seals and other components. Gear with double circular arc sine curve profile manufacturing.With the involute gear is the most prominent advantages of meshing gear tooth profile surface during the no relative sliding, so no tooth wear, smooth running, because no liquid,low noise, long service life, high efficiency. The pump to get rid of the shackles of the traditional design, the gear pump in the design, production and use entered a new field.
3GR螺桿泵設有3GR螺桿泵作為超載保護,3GR螺桿泵全回流壓力為泵額定排出壓力的1.5倍。也可在允許排出壓力范圍內根據實際需要另行調整。但注意本3GR螺桿泵不能作減壓閥*工作,需要時可在管路上另行安裝。
3GR screw pump with 3GR screw pump as overload protection, 3GR screw pump full back pressure 1.5 times the rated discharge pressure of pump. Also allow the discharge pressure in the range according to the actual need to be adjusted. But note that this 3GR screw pumpcan not be valves need long-term work, can be installed in the pipeline.
3GR螺桿泵軸端密封設計為兩種形式,一種為機械密封,一種是填料密封,可根據具體使用情況和用戶要求確定。
3GR screw pump shaft seal is designed to end in two forms, one for the mechanical seal, one is packing seal, can be determined according to the specific conditions and user requirements.
3GR螺桿泵啟動前準備
Preparation of 3GR screw pump start before the
一、啟動前檢查全部管路法蘭,接頭的密封性。
Before starting, check all the pipe flange, joint sealing.
二、盤動聯軸器,無摩擦及碰撞聲音,旋轉順暢。
Two, the dynamic coupling drive, no friction and collision sound, smooth rotation.
三、啟動前應全開吸入和排出管路中的閥門,嚴禁閉閥啟動。
Three, should be fully open before the start of suction and discharge pipe valves, it is strictly prohibited to close the valve to start.
四、驗證電機轉動方向后,啟動電機。
Four, verify the motor rotation direction, start the motor.
五、開機使用
Five, using the boot
3GR螺桿泵校驗與維修
Check and repair of 3GR screw pump
校驗是3GR螺桿泵試驗的一部分,是制造廠出廠試驗的主要項目。出廠前一般都用常溫的3GR螺桿泵校驗臺進行空氣介質的開啟壓力整定和密封性試驗。3GR螺桿泵常溫校驗臺只能做開啟壓力整定和密封性試驗。
Check is a part of the 3GR screw pump test, is the main project manufacturing factory test.The factory is used 3GR screw pump tester at room temperature air opening pressure of the medium setting and sealing tests. 3GR screw pump room temperature calibrator can only doopen the pressure setting and sealing tests.
公 司 名稱: | 黃山天曼泵業有限公司 |
姓名: | 程曉 (銷售 ) () |
辦 公 地址: | 中國 黃山市徽州區城北工業園 |
郵 編: | 245400 |
電 話: | 86-0559-7502919 |
傳 真: | 86-0559-2324433 |
移 動 : | |
郵 箱: | Hstmby01 |
: | : |
阿 里 旺旺: | 旺旺:hstmby01 |
公司主頁: | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao (Sales Manager) ()
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc