SMH80R54E6.7W23SMH80R54E6.7W23三螺桿泵、窯頭點火油泵裝置
【簡單介紹】
【詳細說明】
SMH80R54E6.7W23三螺桿泵、窯頭點火油泵裝置
點火燃油泵的安全使用及維護
Ignition of safe use and maintenance of the fuel pump
1、安裝漏電保護器
1, the installation of leakage protector
漏電保護器也叫保命器,它的作用從“保命器”這三個字就可以理解。因?yàn)辄c(diǎn)火燃油泵在油下工作,容易漏電造成電能損失甚至引發觸電事故。如果裝有漏電保護器,只要點火燃油泵漏電值超過漏電保護器的動作電流值(一般不超過30毫安),漏電保護器就會切斷點火燃油泵的電源,避免漏電浪費電能,確保安全。
Leakage protector, also known as life insurance, it can be understood from the "this three word life insurance".Because the ignition fuel pump in oil, easy to leakage caused by power loss or even lead to electric shock. If there is a leakage protector, as long as the ignition fuel pump leakage exceeds the action leakage protection current value (generally not more than 30 MA), electric leakage protection device will cut off the ignition of the fuel pumppower, to avoid wasting electricity leakage, to ensure safety.
2、電源電壓異常莫開機
2, Mo power supply voltage abnormality
農村由于低壓供電線路比較長,線路的末端電壓過低是常有的事。當相電壓低于198伏,線電壓低于342伏時,點火燃油泵電機轉速下降,當達不到額定轉速的70%時,啟動離心開關會閉合,造成啟動繞組長時間通電而發熱甚至燒壞繞組和電容器。相反,電壓過高引起電機過熱而燒壞繞組。因此,點火燃油泵在作業中,操作者必須隨時觀察電源電壓值,若低于額定電壓10%以下,高于額定電壓10%以上,應使電機停止運轉,找出原因并排除故障。
Low-voltage power lines in rural areas as long, terminal voltage is low line is constant some thing. When the phase voltage below 198 volts, the line voltage is lower than 342 volts, the ignition fuel pump motor speed down,when up to 70% less than the rated speed, the centrifugal start switch closed, resulting in start winding electricityand heat and even burn winding and capacitor. On the contrary, caused by high voltage motor overheating and burn winding. Therefore, the ignition of fuel pump in operation, the operator must always observe the power supply voltage value, if less than the rated voltage below 10%, higher than the rated voltage above 10%, should the motor stop running, find out the reasons and troubleshooting.
3、莫讓點火燃油泵*超負荷工作
3, do not let the ignition fuel pump overload
為避免潛油電泵*超負荷工作,不要抽含沙量大的油并隨時觀察電流值是否在銘牌上規定的數值,若發現電流過大,應停機檢查。另外,電泵脫油運行的時間不宜過長,以免使電機過熱而燒毀。
In order to avoid the electric submersible pump long-term overload of work, numerical do not draw large sedimentoil and observe whether the current value specified on the nameplate, if too much current is found, should be down to check. In addition, the electric pump oil removing operation time should not be too long, to avoid overheating and burning motor.
SMH三螺桿泵主要應用:
SMH three screw pump is mainly used:
高壓蒸汽鍋爐燃油輸送;
High pressure steam boiler fuel delivery;
船舶工業,柴油發動機,渦輪鍋爐等;
Shipbuilding industry, diesel engine, turbine boiler etc.;
燃油輸送系統應用;
Application of the fuel delivery system;
傳送介質范圍:
The transmission medium range:
船用柴油,汽油(MDO,MGO),重型燃油HFO,車用燃油,生物油等
Marine diesel, gasoline (MDO, MGO) HFO, heavy fuel, vehicle fuel, bio oil
產品說明:
Product description:
可以提供電機+螺桿泵組裝成套供貨,附帶吸油管道和支架等,以及完整的測試報告;
Can provide motor and screw pump assembly and delivery, incidental suction pipe and the support, and a complete test report;
可以提供壓力安全閥組等配套附件;
Can provide pressure relief valve group and other accessories;
可選擇徑向或軸向吸油口,SAE法蘭BSPP或螺紋連接;
Can choose the radial or axial suction port of SAE BSPP or threaded connection, flange;
螺桿泵體表面特殊處理,硬度為63HRC;重載機械密封,
Screw pump with special surface treatment, hardness is 63HRC; heavy duty mechanical seal,
螺桿泵外部護套(可選)材質為AMSE標準,可根據API標準制造;
Screw pump outer sheath (optional) made of AMSE standards, can be manufactured according to API standard;
螺桿硬度為63HRC,超精密加工;
Screw the hardness is 63HRC, ultra precision machining;
介質的zui低允許黏度為2cst,zui高1000cst,允許zui大顆粒物30um.
Medium viscosity minimum allowed is 2cst, maximum 1000cst, maximum 30um. particles
螺桿泵zui高壓力達8MPa;
The highest pressure screw pump up to 8MPa;
流量范圍:0-2000L/min
Flow range: 0-2000L/min
SMH三螺桿泵簡介Introduction to SMH three screw pump
一、特點 One, characteristic
SM三螺桿泵 SM three screw pump
1.SMH高壓三螺桿泵是利用轉子液壓平衡技術,所以在工作時候振動小,噪音低。
1.SMH high voltage three screw pump is the use of hydraulic balancing rotor, so the work when small vibration, low noise
2.SMH輸出穩定,工作時無脈動。
2.SMH output stability, work without pulsation.
3.SMH點火油泵的工作效率高。
3.SMH ignition oil pump with high efficiency.
4.SMH三螺桿泵具有很強的自吸能力。
4.SMH three screw pump has a strong self absorption capacity.
5.SMH燃油輸送泵結構簡單具有很強的互換性,還能根據使用現場的條件,安裝成SMH臥式安裝三螺桿泵,SMF支架式安裝三螺桿泵,SMS立式安裝三螺桿泵,如有特殊要求還可以訂做。
5.SMH fuel pump has the advantages of simple structure, a strong interchangeability, can according to the siteconditions, installation of an SMH SMF three screw pump horizontal installation, scaffolding installation of three screw pump, SMS vertical installation of three screw pump, if there are special requirements can also becustomized.
6.SMH熱電廠用點火油泵具有結構緊湊,體積小,重量輕,可在較高轉速下工作。
6.SMH power plant ignition oil pump has the advantages of compact structure, small volume, light weight, can be in high speed.
歡迎廣大新老客戶、訂貨,垂詢:
公 司 名稱: | 黃山天曼泵業有限公司 |
姓名: | 程曉 (銷售 ) () |
辦 公 地址: | 中國 黃山市徽州區城北工業園 |
郵 編: | 245400 |
電 話: | 86- |
傳 真: | 86- |
移 動 : | |
郵 箱: | Hstmby01 |
: |
|
阿 里 旺旺: | 旺旺:hstmby01 |
公司主頁: | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao (Sales Manager) ()
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc
相關產品
- SMH80R36E6.7W23SMH80R36E6.7W23三螺桿泵 SM高壓油泵
- SMH40R54E6.7W23SMH40R54E6.7W23三螺桿泵 SM系列高壓油泵
- SMH40R46E6.7W23SMH40R46E6.7W23三螺桿泵、中高壓油泵
- SMH40R38E6.7W23SMH40R38E6.7W23三螺桿泵、全國高壓螺桿泵
- SMH120R54E6.7W23SMH120R54E6.7W23三螺桿泵、高壓SM三螺桿泵
- SMH120R46E6.7W23SMH120R46E6.7W23三螺桿泵、電廠點火油泵
- SMH120R42E6.7W23SMH120R42E6.7W23三螺桿泵、全國質量保證
- SMH80R54E6.7W23SMH80R54E6.7W23三螺桿泵、SM系列高壓泵
- SMH80R46E6.7W23SMH80R46E6.7W23三螺桿泵、柴油輸送泵
- SMH80R42E6.7W23SMH80R42E6.7W23三螺桿泵、優質高壓油泵
- SMH80R36E6.7W23SMH80R36E6.7W23三螺桿泵、窯頭點火油泵
- SMH40R54E6.7W23SMH40R54E6.7W23三螺桿泵、鍋爐點火油泵
- SMH40R46E6.7W23SMH40R46E6.7W23三螺桿泵、黃山螺桿泵
- SMH80R46E6.7W28SMH80R46E6.7W28三螺桿泵、重油輸送泵
- SMH80R42E6.7W28SMH80R42E6.7W28三螺桿泵
- SMH40R54E6.7W23SMH40R54E6.7W23三螺桿泵、品牌三螺桿泵
- SMH40R46E6.7W23SMH40R46E6.7W23三螺桿泵、臥式高壓油泵
- SMH80R36E6.7W23SMH80R36E6.7W23三螺桿泵、優質螺桿泵供應商
- SMH40R54E6.7W23SMH40R54E6.7W23三螺桿泵、金品質螺桿泵
- SMH40R46E6.7W23SMH40R46E6.7W23三螺桿泵、5*螺桿泵供應
- SMH40R38E6.7W23SMH40R38E6.7W23三螺桿泵、熱電廠點火油泵
- SMH120R54E6.7W28SMH120R54E6.7W28三螺桿泵
- SMH120R46E6.7W28SMH120R46E6.7W28三螺桿泵
- SMH120R42E6.7W28SMH120R42E6.7W28三螺桿泵
- SMH80R54E6.7W28SMH80R54E6.7W28三螺桿泵
- SMH80R46E6.7W28SMH80R46E6.7W28三螺桿泵
- SMH80R42E6.7W28SMH80R42E6.7W28三螺桿泵
- SMH80R36E6.7W28SMH80R36E6.7W28三螺桿泵
- SMH40R54E6.7W28SMH40R54E6.7W28三螺桿泵
- SMH40R46E6.7W28SMH40R46E6.7W28三螺桿泵
- SMH40R38E6.7W28SMH40R38E6.7W28三螺桿泵
- SMH80R46E6.7W28節能螺桿泵SMH80R46E6.7W28三螺桿泵
- SMH80R36E6.7W28節能螺桿泵SMH80R36E6.7W28三螺桿泵
- SMH40R54E6.7W28節能螺桿泵SMH40R54E6.7W28三螺桿泵
- SMH40R46E6.7W28節能螺桿泵SMH40R46E6.7W28三螺桿泵
- SMH40R38E6.7W28節能螺桿泵SMH40R38E6.7W28三螺桿泵
- SMH120R54E6.7W23品質,輝煌天曼SMH120R54E6.7W23三螺桿泵
- SMH120R46E6.7W23品質,輝煌天曼SMH120R46E6.7W23三螺桿泵
- SMH120R42E6.7W23品質,輝煌天曼SMH120R42E6.7W23三螺桿泵
- SMH80R54E6.7W23品質,輝煌天曼。SMH80R54E6.7W23三螺桿泵
請輸入產品關鍵字: