SNH80R54U8W27SNH80R54U8W27三螺桿泵、冷卻系統電廠透平油輸送泵
【簡單介紹】
【詳細說明】
SNH80R54U8W27三螺桿泵、冷卻系統電廠透平油輸送泵
品牌:黃山天曼泵業
SNH80R54U12.1W2三螺桿泵 SNH80R54U12.1W21三螺桿泵 SNH80R54U12.1W23三螺桿泵
SNH80R54UM3NW2三螺桿泵 SNH80R54UM3NW21三螺桿泵 SNH80R54UM3NW23三螺桿泵
SNH80R54U8W2三螺桿泵 SNH80R54U8W21三螺桿泵 SNH80R54U8W23三螺桿泵
SNH80R54E6.7W2三螺桿泵 SNH80R54E6.7W21三螺桿泵 SNH80R54E6.7W23三螺桿泵
流量:102.5l/min
壓力:1.0Mpa
功率: 2.1kw
轉速:1450r/min
驅動方式:電機驅動
進出口徑:65mm 50mm
SN螺桿泵振動產生的原因和隔振方法
SN screw pump vibration and vibration isolation method
一、SN螺桿泵振動產生原因
A, SN screw pump vibration causes
1.由于SN螺桿泵制造工藝不過關:轉子不平衡;泵與電機軸不同心;轉子與定子部分發生碰撞或磨擦;
2.由于使用時間較長,SN螺桿泵磨損老化:葉輪松動;軸承損壞或軸承間隙大;
3.SN螺桿泵入口管、葉輪內、泵內有雜物;SN螺桿泵與基礎固定不緊固,發生共振加強現像等;
4.SN螺桿泵工作中推進油流時,伴隨的渦流,氣蝕不可避免的會產生振動;
由此,我們可以得出結論:SN螺桿泵產生振動的原因很多,其中一些很多振動的產生幾呼是不可避免的。這就要求我們對于處置SN螺桿泵振動問題除對SN螺桿泵本身制造工藝進行加強,降低振動幅度外,通過給SN螺桿泵安裝橡膠隔振器、彈簧隔振器、隋性基座也成為SN螺桿泵振動控制重要方法。
1 since SN screw pump manufacturing process does not pass: the imbalance of the rotor; the pump and motor shaft misalignment; the rotor and the stator part collision or friction;
2 because of the use of longer, SN screw pump impeller wear: loose; bearing damage orlarge bearing clearance;
3.SN screw pump, impeller, pump entrance pipe inside; SN screw pump and the fixed basefastening, resonance strengthen now like etc.;
Push the oil flow in the screw pump with 4.SN, vortex, cavitation will inevitably producevibration;
Thus, we can draw the conclusion: many vibration causes the SN screw pump, which produced some vibration few call is inevitable. This requires us to deal with SN screw pumpvibration problem in addition to strengthening of SN screw pump itself manufacturing process,reduce the vibration amplitude, through to the SN screw pump installation of rubber isolator,spring vibration isolator, the Sui base has become the important method for vibration control of SN screw pump.
二、SN螺桿泵振動的控制治理:
A.加裝彈簧隔振器:
a.SN螺桿泵彈簧隔振器樣式的選擇:
一般選用自立式彈簧減振器,其優點結構簡單、造價較低;彈簧裸露在外,便于隨時觀察彈簧狀態,對于需更換的彈簧提前處置,以避免彈簧銹蝕過度損壞時,造成SN螺桿泵突然沉降造成設備損害及管路扯斷等現像。
b.彈簧的選擇:
一般減振器廠家選用彈簧需滿足以下要求:彈簧直徑應不少于其在額定負載下高度的0.8倍;彈簧須具備一定的額外行程,渦街流量計至少等于額定靜撓度的50%;彈簧的油平剛度至少是堅直鋼度的*,以保證減振器的穩定性?!?br />c.彈簧減振器撓度的選擇;
通常減振器廠商所提拱的彈簧減振器額定撓度(彈簧額定壓縮量)一般為25MM(自頻率值約3-4HZ),此撓度可應于650轉每分鐘的SN螺桿泵的隔振。當轉速低于650時,建議使用40以下?lián)隙戎畯椈筛粽衿?。?br />B。加裝橡膠隔振器:
橡膠隔振器之選擇:材質一般為氯丁膠(C.R),天然膠(N.R);一般選用壓縮型橡膠減振器,對于重量較輕的SN螺桿泵,可選用剪切型橡膠減振器;
相較彈簧減振器,橡膠減振器隔振性能相對相差些?!?br />C.加裝隋性基座:
為滿足更加嚴格的振動制標準,加裝隋性基座時,配合使用彈簧隔振器,無疑是的選擇。
隋性基座的規范:基座重量約為SN螺桿泵重量1-2倍以上;框架由槽鐵鎖固而成,其高度不少于長度的1/12,但不低于150MM,不高于300MM;長寬尺寸應能將整個SN螺桿泵涵蓋在內,并各邊余10-15公分為宜。并且能將灣頭也涵蓋在內;內澆灌油泥,并內置一層鋼筋網于高度之三分之一處;加裝彈簧隔振器將基座與基礎間距至3-5公分?!?/p>
Control, SN two screw pump vibration:
A. with spring vibration isolator:
A.SN screw pump spring vibration isolator style choice:
General selection of self-supporting spring shock absorber, which has the advantages ofsimple structure, low cost; spring is exposed outside, easy to observe the spring state, for thespring to be replaced early treatment, to avoid excessive damage caused by spring corrosion, SN screw pump sudden subsidence caused by equipment damage and pipelinebreak, we like.
B. choice of spring:
Common damper manufacturers choose to use spring shall meet the following requirements:spring diameter shall be not less than the rated load is 0.8 times the height of the spring must have certain travel; additional, vortex flowmeter is at least equal to the rated static deflection of 50%; spring oil horizontal stiffness is at least * vertical stiffness, in order to ensure thestability of the vibration damper the.
C. spring damper deflection choice;
Usually damper manufacturers the rated deflection spring shock absorber arch (rated springcompression) is generally 25MM (self frequency value of about 3-4HZ), the deflection can bethe isolation from 650 to SN per minute of the screw pump. When the speed is lower than 650, suggested using the 40 deflection spring isolator.
B. Installing the rubber vibration isolator:
Rubber isolator material selection: General chloroprene rubber (C.R), natural rubber (N.R);general selection of compression type rubber shock absorber, for the SN screw pump light weight, can choose a shear type rubber damper; compared with the spring and damper,rubber shock absorber vibration isolation performance relative phase difference.
C. install the Sui base:
Vibration system to meet the more stringent standards, with the Sui base, with spring vibration isolator, is undoubtedly the best choice. The Sui base specification: the base weightof about SN screw pump weight more than 1-2 times; frame by groove carabiners and fixing,the height is not less than the length of the 1/12, but not less than 150MM, not more than300MM; the length and width dimensions should be able to take the entire SN screw pumpcover, and each side more than 10-15 cm is appropriate. And can be the best bay headcovered in water; sludge, and built a layer of steel net in height 1/3; with spring vibration isolator interval between the base and the base to 3-5 cm.
二、SN螺桿泵振動控制治理效果:
基于SN螺桿泵設備情況,通過上述方法處理可達到85-99%以上的隔振效果,從而從根本上解決SN螺桿泵振動帶給人們生活,及工業生產的困擾。
Two, SN screw pump vibration control effect:
SN screw pump equipment based on the vibration isolation effect, can achieve more than 85-99% by using the method of treatment, so as to solve the vibration of SN screw pump to bring people to life fundamentally, distress and industrial production.
SNH系列三螺桿泵型號大全:
一、 SN40系列三螺桿泵
SNH40R38U12.1W2三螺桿泵
SNH40R46U12.1W2三螺桿泵
SNH40R54U12.1W2三螺桿泵
二、 SN80系列三螺桿泵
SNH80R36U12.1W2三螺桿泵
SNH80R42U12.1W2三螺桿泵
SNH80R46U12.1W2三螺桿泵
SNH80R54U12.1W2三螺桿泵
三、 SN120系列三螺桿泵
SNH120R42U12.1W2三螺桿泵
SNH120R46U12.1W2三螺桿泵
SNH120R54U12.1W2三螺桿泵
四、 SN210系列三螺桿泵
SNH210R40U12.1W2三螺桿泵
SNH210R46U12.1W2三螺桿泵
SNH210R54U12.1W2三螺桿泵
五、 SN280系列三螺桿泵
SNH280R43U12.1W2三螺桿泵
SNH280R46U12.1W2三螺桿泵
SNH280R54U12.1W2三螺桿泵
六、 SN440系列三螺桿泵
SNH440R40U12.1W2三螺桿泵
SNH440R42U12.1W2三螺桿泵
SNH440R46U12.1W2三螺桿泵
SNH440R54U12.1W2三螺桿泵
七、 SN660系列三螺桿泵
SNH660R40U12.1W2三螺桿泵
SNH660R44U12.1W2三螺桿泵
SNH660R46U12.1W2三螺桿泵
SNH660R51U12.1W2三螺桿泵
SNH660R54U12.1W2三螺桿泵
八、 SN940系列三螺桿泵
SNH940R42U12.1W2三螺桿泵
SNH940R46U12.1W2三螺桿泵
SNH940R50U12.1W2三螺桿泵
SNH940R54U12.1W2三螺桿泵
九、 SN1300系列三螺桿泵
SNH1300R38U12.1W2三螺桿泵
SNH1300R42U12.1W2三螺桿泵
SNH1300R46U12.1W2三螺桿泵
SNH1300R54U12.1W2三螺桿泵
十、 SN1700系列三螺桿泵
SNH1700R42U12.1W2三螺桿泵
SNH1700R46U12.1W2三螺桿泵
十一、SN2200系列三螺桿泵
SNH2200R42U12.1W2三螺桿泵
SNH2200R46U12.1W2三螺桿泵
十二、SN2900系列三螺桿泵
SNH2900R40U12.1W2三螺桿泵
SNH2900R46U12.1W2三螺桿泵
十三、SN3600系列三螺桿泵
SNH3600R46U12.1W2三螺桿泵
十四、SN5300系列三螺桿泵
SNH5300R46U12.1W2三螺桿泵
公 司 名稱: | 黃山天曼泵業有限公司 |
姓名: | 程曉 (銷售 ) () |
辦 公 地址: | 中國 黃山市徽州區城北工業園 |
郵 編: | 245400 |
電 話: | 86- |
傳 真: | 86- |
移 動 : | |
郵 箱: | Hstmby01 |
: |
|
阿 里 旺旺: | 旺旺:hstmby01 |
公司主頁: | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao (Sales Manager) ()
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc
相關產品
- SNH80R36U12.1W21SNH80R36U12.1W21三螺桿泵 鑄銅泵芯總成
- SNH40R54U12.1W21SNH系列三螺桿泵、黃山螺桿泵
- SNH40R46U12.1W21SNH40R46U12.1W21三螺桿泵 全國質量保證
- SNH80R36U8W2SNH80R36U8W2三螺桿泵 SNH系列
- SNH80R46U12.1W21SNH80R46U12.1W21三螺桿泵 現貨供應
- SNH80R42U12.1W21SNH80R42U12.1W21三螺桿泵 質量*廠家
- SNH80R36U12.1W21SNH80R36U12.1W21三螺桿泵 SN系列螺桿泵
- SNH40R54U12.1W21SNH40R54U12.1W21三螺桿泵 三螺桿泵大全
- SNH40R46U12.1W21SNH40R46U12.1W21三螺桿泵 *
- SNH40R38U12.1W21SNH40R38U12.1W21三螺桿泵 電廠油泵
- SNH120R54U8W2SNH120R54U8W2三螺桿泵、*、
- SNH120R46U8W2SNH120R46U8W2三螺桿泵、臥式安裝
- SNH120R42U8W2SNH120R42U8W2三螺桿泵、金品質*三螺桿泵
- SNH80R54U8W2三螺桿泵SNH80R54U8W2三螺桿泵、高效節能三螺桿泵
- SNH80R46U8W2三螺桿泵SNH80R46U8W2三螺桿泵、高效率三螺桿泵
- SNH80R42U8W2三螺桿泵SNH80R42U8W2三螺桿泵、優質螺桿泵組
- SNH80R36U8W2三螺桿泵SNH80R36U8W2三螺桿泵、SN系列工業泵
- SNH40R54U8W2三螺桿泵SNH40R54U8W2三螺桿泵、液壓系統輸送泵
- SNH40R46U8W2三螺桿泵SNH40R46U8W2三螺桿泵、黃山SN系列三螺桿泵
- SNH40R38U8W2三螺桿泵SNH40R38U8W2三螺桿泵、SN系列螺桿泵
- SNH80R46U12.1W21SNH80R46U12.1W21三螺桿泵、全國*產品
- SNH80R42U12.1W21SNH80R42U12.1W21三螺桿泵
- SNH80R36U12.1W21SNH80R36U12.1W21三螺桿泵、天曼螺桿泵
- SNH40R54U12.1W21SNH40R54U12.1W21三螺桿泵、螺桿泵*質保
- SNH40R46U12.1W21SNH40R46U12.1W21三螺桿泵、SN系列三螺桿泵
- SNH40R38U12.1W21SNH40R38U12.1W21三螺桿泵、現貨供應
- SNH120R54U8W2SNH120R54U8W2三螺桿泵、螺桿泵中的戰斗機
- SNH120R46U8W2SNH120R46U8W2三螺桿泵、金品質三螺桿泵
- SNH120R42U8W2SNH120R42U8W2三螺桿泵、螺桿泵泵芯總成
- SNH80R54U8W2SNH80R54U8W2三螺桿泵、優質螺桿泵供應商
- SNH80R46U8W2SNH80R46U8W2三螺桿泵、(天曼螺桿泵)
- SNH80R42U8W2SNH80R42U8W2三螺桿泵、品質、輝煌天曼
- SNH80R36U8W2SNH80R36U8W2三螺桿泵、優質三螺桿泵
- SNH40R54U8W2SNH40R54U8W2三螺桿泵、5*三螺桿泵
- SNH40R46U8W2SNH40R46U8W2三螺桿泵、螺桿泵裝置
- HSNS40-46NZ三螺桿泵天曼制造HSNS40-46NZ三螺桿泵
- SNH120R54U12.1W21SNH120R54U12.1W21三螺桿泵、
- SNH120R46U12.1W21SNH120R46U12.1W21三螺桿泵、5星級螺桿泵廠家
- SNH120R42U12.1W21SNH120R42U12.1W21三螺桿泵
- SNH80R54U12.1W21SNH80R54U12.1W21三螺桿泵、優質螺桿泵裝置
請輸入產品關鍵字: