SMH120R46E6.7W30三螺桿泵、臥式SM系列冷卻液輸送泵
如何進行三螺桿泵配套機械密封的更換安裝，必須遵循以下幾點：
How to replace the three screw pump mechanical seal installation, the following points must be observed:
（1）螺桿泵出廠序列號、機械密封的型號、規格是否正確以及是否為帶有黃山天曼泵業有限公司三螺桿泵機械密封件標識標志，質量是否符合標準；密封安裝前，應確認產品型號及規格與設備要求*
（1） the screw pump mechanical seal factory serial number, type, specification is correct and whether with Mount Huangshan teamon pump industry limited company machinery three screw pump seal logo, quality standards;seal before installation, should confirm the product types and specifications and equipment requirements.
（2）靜環尾部防轉槽端與防轉銷頂部應保持1mm-2mm的軸向間隙，以免緩沖失效。
（2） the static ring tail anti rotary slot end and the anti rotation pin top should maintain the axial clearance of 1mm-2mm, so as to avoid the buffer invalidation.
（3）動、靜環端面用酒精清洗干凈，其余金屬件用汽油清洗并用潔凈的壓縮空氣吹干，仔細檢查務必保證動、靜環密封面沒有任何損傷。損傷和破裂的均不能更換。裝配前，兩件“O”形橡膠密封圈應涂上機械密封標準一層潤滑油膏，動、靜環端面不許涂油。
（3） dynamic, static ring tip with alcohol to clean, and other metal parts cleaning with gasoline and clean compressed air dryer, carefully check must ensure that the dynamic, static ring sealing surface without anydamage. Damage and can not be broken replacement. Before the assembly, the two "O" shaped rubber sealing ring should be coated with a layer of lubricating grease standard mechanical seal, dynamic, not static ring oiler.
（4）在安裝密封的軸，腔體及壓蓋等與輔助密封圈接觸處均勻涂油（注：對乙丙橡膠、或介質不允許注入潤滑油的情況下，可涂抹植物油或肥皂水。把機械密封套上軸，按設計的工作高度安裝到位。過壓蓋通孔，采用對角線交叉擰緊方式，用螺栓將整個密封與密封腔體（泵蓋）聯接擰緊機械密封配有輔助系統時，按標示正確連接管路。
（4） in the installation of the sealing shaft, cavity and a gland and auxiliary seal ring contact uniform oiling （Note:ethylene propylene rubber, or the media are not allowed into the lubrication condition, can apply vegetable oil orsoap and water. The mechanical sealing sleeve shaft, according to design the working height of the installed in place. Overvoltage cover through hole, the diagonal cross screw, bolt the entire seal and seal cavity （cover）connected tighten the mechanical seal fitted with auxiliary system, marked by the pipeline connecting the right.
（5）在三螺桿泵轉子與泵體的相對位置固定之后，確定機械密封的安裝位置，根據密封的安裝尺寸及靜環在壓蓋中的位置，測算出密封在軸或軸套上的定位尺寸。
（5） after the relative positions of the three screw pump rotor and pump body is fixed, to determine the installation position of mechanical seal, according to the size and position of the installation of sealing static ring in the gland,calculate the location dimension seal in the shaft or shaft sleeve.
（6）安裝機封動環，動環安裝后須保證能其在軸上靈活移動。
（6） mounted machine sealing ring, ring after installation shall ensure that its flexible move on the shaft.
（7）將組裝好的靜環部分和動環部分組裝好。
（7） the assembled static ring and moving ring partially assembled.
（8）把密封端蓋裝在密封體內，并將螺絲擰緊。
（8） the sealing end cover is arranged in the sealing body, and the screw.
（9）試車：以上步驟完成后，手動盤車三螺桿泵配套機械密封，注意觀察轉矩的變化，以及有無擦碰聲音異常等，以確定是否要重新安裝和調整。
（9） test: after the above steps, manual turning three screw pump mechanical seal, observe the torque change,and there is no rubbing sound abnormal, to determine whether to re install and adjust.
（10）打開閥門，密封腔內通入密封介質，全部排出密封腔的空氣，使密封腔中全部充滿介質，并觀察封有無泄漏情況。
（10） to open the valve, the sealing cavity communicated with the sealing medium, exhaust all the seal cavity of the air, so that the sealing cavity full of medium, and observe the seal without leakage.
（11）確認上述兩項正確無誤后進行試運轉。
（11） confirmed that the above two correct test run.
（12）機械密封腐蝕防護知識詳解
（12） the mechanical seal corrosion protection knowledge.
（13）表面均勻腐蝕。如果金屬環表面接觸腐蝕介質，而金屬本身又不耐腐蝕，就會產生表面腐蝕，其現象是泄漏、早期磨損、破壞、發聲等。金屬表面均勻腐蝕有成膜和無膜兩種形態，無膜的金屬腐蝕很危險，稱為應力腐蝕破裂，選用堆焊硬質合金及鑄鐵、碳化鎢、碳化鈦等密封環，容易出現應力腐蝕破裂。腐蝕過程以一定的速度進行，使電偶腐蝕加劇?！?/p>
（13） surface uniform corrosion. If the metal contact ring corrosive medium, and the corrosion of the metal itself is intolerant, it will have a surface corrosion, which is leaking, the early wear and tear, damage, such as audible.Uniform corrosion on metal surfaces have two forms of film and without film, corrosion of metal membrane free is dangerous, known as stress corrosion cracking, the selection of welding hard alloy and cast iron, tungsten carbide, titanium carbide seal ring, prone to stress corrosion cracking. The corrosion process to a certain speed,so that aggravate galvanic corrosion.
（14）應力腐蝕破裂。金屬在腐蝕和拉應力的同時作用下，耐磨性。機械密封填充F4環的腐蝕主要是指填充的選擇性腐蝕、溶出或變質破壞。如在氫氟酸中，玻璃纖維分子熱腐蝕，這些裂縫溝通了整個密封端面，加速了端面的磨損，使泄漏量增加。
14） the stress corrosion cracking. Metal corrosion and stress at the same time, wear resistance. Corrosion of mechanical seal ring filled F4 mainly refers to the selective corrosion, filled stripping or destruction of metamorphism. Such as hydrofluoric acid, the hot corrosion of glass fiber elements, these cracks sealed face communication as a whole, to speed up the end of the wear and tear, so that leakage increased.
SM三螺桿泵特點：
1、 自吸式三螺桿泵
2、 轉子液壓平衡，振動小，噪音低
3、 輸出穩定，無脈動，高效率
4、 零部件采用通用性強的系列化設計，具有多種安裝方式。
SM三螺桿泵應用范圍：
用于輸送不含顆粒雜質且沒有腐蝕性的液體。
SM三螺桿泵應用領域：
用途 | 輸送介質 | 應用領域 | 行業列舉 |
燃油點火、噴射 | 輕燃油、重燃油、渣油、廢油 | 能源工程、燃燒器配套和燃油噴射泵（燃?xì)廨啓C(jī)）。 | 熱電、火電、水泥工業、工業鍋爐、燃燒器配套 |
液壓增壓 | 液壓油、潤滑油 | 升降機液壓泵、升降平臺、離心機推進器、油壓式?jīng)_床、鍛錘、大型打包機、碎料板壓機、液壓絞車、起重機、各種螺旋槳推進裝置、槳舵調節裝置、艙口液壓設備、輥軋機液壓裝置及機床液壓裝置等 | 工程機械、船舶重工、鋼鐵冶金、礦山采掘、水泥建材、碼頭港口、液壓、大型機床等 |
工業潤滑 | 潤滑油、冷卻油、切削冷卻液、密封油、液壓油、輕重質燃油、柴油、燃料油、導熱油等 | 水輪機、汽輪機及燃?xì)廨啓C(jī)用密封油泵、調節油泵、頂軸油泵；壓縮機用密封油泵、冷卻循環油泵；柴油機用燃油泵、冷卻循環油泵；軋鋼機用液壓油泵等 | 能源工程（水電、熱電、火電、風電等）、鋼鐵冶金、礦山采掘、水泥建材、海洋工程等。 |
循環冷卻 | 切削油、金屬研磨用冷卻油乳液、深孔鉆切削液、水包油乳化液、機械液壓油等 | 深孔加工中心、數控鉆銑床、大型鏜床、車床鉆頭沖洗鐵屑、工件冷卻、深孔加工排屑、鏜床液壓系統 | 數控機床加工、機械加工等 |
輸送裝卸 | 各種潤滑性液體，如：潤滑脂油、油類、油漆、燃料油、原油、油脂、涂料、油膏、糊料、焦油、瀝青、膠水、膠黏劑、松香酯、石蠟、蠟類、硅酸鈉、油墨、清油漆、亞麻籽油、皂液、添加劑、粘膠纖維、紙漿、糖漿、葡萄糖、糖蜜和植物油等 | 用作裝載泵、卸油泵、管道泵、流程泵、 | 油田油庫、化工、石化煉化、印染造紙、油漆、洗滌凈化、食品工業 |
SM三螺桿泵安裝型式靈活多樣化
結構說明 | 對應子系列 |
臥式地腳安裝泵 | SMH |
端法蘭聯接泵 | SMF |
立式柱腳安裝泵 | SMS |
泵轉子組件，桿套插裝泵 | SME |
進出口同側法蘭聯接泵 | SMB |
公 司 名稱： | 黃山天曼泵業有限公司 |
姓名： | 程曉 （銷售 ） （） |
辦 公 地址： | 中國 黃山市徽州區城北工業園 |
郵 編： | 245400 |
電 話： | 86- |
傳 真： | 86- |
移 動 ： | |
郵 箱： | Hstmby01 |
： |
|
阿 里 旺旺: | 旺旺：hstmby01 |
公司主頁： | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao （Sales Manager） （）
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc
