SMH80R42E6.7W23三螺桿泵、高壓SM系列螺桿泵組
點火燃油泵的安全使用及維護
Ignition of safe use and maintenance of the fuel pump
1、安裝漏電保護器
1, the installation of leakage protector
漏電保護器也叫保命器，它的作用從“保命器”這三個字就可以理解。因?yàn)辄c(diǎn)火燃油泵在油下工作，容易漏電造成電能損失甚至引發觸電事故。如果裝有漏電保護器，只要點火燃油泵漏電值超過漏電保護器的動作電流值（一般不超過30毫安），漏電保護器就會切斷點火燃油泵的電源，避免漏電浪費電能，確保安全。
Leakage protector, also known as life insurance, it can be understood from the "this three word life insurance".Because the ignition fuel pump in oil, easy to leakage caused by power loss or even lead to electric shock. If there is a leakage protector, as long as the ignition fuel pump leakage exceeds the action leakage protection current value （generally not more than 30 MA）, electric leakage protection device will cut off the ignition of the fuel pumppower, to avoid wasting electricity leakage, to ensure safety.
2、電源電壓異常莫開機
2, Mo power supply voltage abnormality
農村由于低壓供電線路比較長，線路的末端電壓過低是常有的事。當相電壓低于198伏，線電壓低于342伏時，點火燃油泵電機轉速下降，當達不到額定轉速的70%時，啟動離心開關會閉合，造成啟動繞組長時間通電而發熱甚至燒壞繞組和電容器。相反，電壓過高引起電機過熱而燒壞繞組。因此，點火燃油泵在作業中，操作者必須隨時觀察電源電壓值，若低于額定電壓10%以下，高于額定電壓10%以上，應使電機停止運轉，找出原因并排除故障。
Low-voltage power lines in rural areas as long, terminal voltage is low line is constant some thing. When the phase voltage below 198 volts, the line voltage is lower than 342 volts, the ignition fuel pump motor speed down,when up to 70% less than the rated speed, the centrifugal start switch closed, resulting in start winding electricityand heat and even burn winding and capacitor. On the contrary, caused by high voltage motor overheating and burn winding. Therefore, the ignition of fuel pump in operation, the operator must always observe the power supply voltage value, if less than the rated voltage below 10%, higher than the rated voltage above 10%, should the motor stop running, find out the reasons and troubleshooting.
3、莫讓點火燃油泵*超負荷工作
3, do not let the ignition fuel pump overload
為避免潛油電泵*超負荷工作，不要抽含沙量大的油并隨時觀察電流值是否在銘牌上規定的數值，若發現電流過大，應停機檢查。另外，電泵脫油運行的時間不宜過長，以免使電機過熱而燒毀。
In order to avoid the electric submersible pump long-term overload of work, numerical do not draw large sedimentoil and observe whether the current value specified on the nameplate, if too much current is found, should be down to check. In addition, the electric pump oil removing operation time should not be too long, to avoid overheating and burning motor.
4、避免頻繁開關
4, to avoid frequent switching
不要頻繁地開關點火燃油泵，這是因?yàn)殡姳猛＾D(zhuǎn)時會產生回流，若立即開機，會使電機負載啟動，導致啟動電流過大而燒壞繞組。由于啟動時電流很大，頻繁啟動也會燒壞點火燃油泵電動機繞組。
The ignition of fuel pump do not frequently switch, this is because the pump will stop to have a return, if an immediate start, will start the motor load, resulting in excessive starting current and burn winding. As the start when the current large, frequent starts will burn the fuel pump motor ignition winding.
Insulation resistance
5、電纜線安裝與潛油電泵的絕緣電阻要求
5, cable installation and electric submersible pump
安裝點火燃油泵時，電纜線要架空，電源線不要太長。點火燃油泵下油或提出時切勿使電纜受力，以免引起電源線斷裂。點火燃油泵工作時不要沉入泥中，否則會導致電機散熱不良而燒壞電機繞組。安裝時，電機的絕緣電阻不應低于0.5兆歐。
Install ignition fuel pump, to the overhead cable, power line should not be too long. Ignition fuel pump oil or propose not to force the cable, so as not to cause a power line fault. Ignition fuel pump work do not sink into the mud, or would result in poor motor cooling motor windings burned. When in installation, insulation resistanceshould not be less than 500000000000 ohm motor.
6、電機的旋轉方向要正確
The direction of rotation, the motor 6 to the right
應搞清電機的旋轉方向，現在有許多類型的點火燃油泵正轉和反轉時皆可出油，但反轉時出油量小、電流大，其反轉時間長了會損壞電機繞組。
We should understand the direction of motor rotation, there are many types of ignition of fuel pump when the forward and reverse can be out of oil, but the reverse when the oil quantity is small, current, its reversal long time may damage the motor windings.
7、勤查勤看發現問題及時修復
7, Qin Chaqin see repair problems in a timely manner
平時要經常檢查電機，如發現下蓋有裂紋、橡膠密封環損壞或失效等，應及時更換或修復，避免油滲入點火燃油泵。
Usually should always check the motor, such as a crack was found under the lid, rubber seal ring damage or failure, should be timely replacement or repair, oil into the ignition fuel pump to avoid.
公 司 名稱： | 黃山天曼泵業有限公司 |
姓名： | 程曉 （銷售 ） （） |
辦 公 地址： | 中國 黃山市徽州區城北工業園 |
郵 編： | 245400 |
電 話： | 86- |
傳 真： | 86- |
移 動 ： | |
郵 箱： | Hstmby01 |
： |
|
阿 里 旺旺: | 旺旺：hstmby01 |
公司主頁： | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao （Sales Manager） （）
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc
